Product Carousel Tabs
AMF / ATS Controller, Generator, Genset Starting Module
DTA-912 Digital Duel Fuel Control System
DTA-912 Digital Duel Fuel Control System
Microprocessor controled
Front panel mounting
Front panel programming
Ldc Display
Five Relay control card
Uses gas to reduce diesel consumption
As the load on the generator increases, the gas valve will open.
In case of low load, the valve will be shut down automatically.
Study the installation diagram for more information and to understand the card
SKU: n/a
DC Motor Drive, Motor Drive's
DTA-1514 DC Motor Drive 12V,24V 20A
FEATURES
Model No: DTA-1514
Input Voltage: 30v DC
Out Voltage: 2V to 24V DC
Current: 20A
Technology: PWM
Speed Control With Volume
Switch For Strat & Stop
Size: Approx. 100 x 95 x 40mm
Input Output Led Indicators
Easy to Install
SKU: n/a
AVR, Generator
DTA-226 Consealed AVR Automatic Voltage Regulator For Generator
feature keys
Model No DTA-226 Consealed
This model is specially designed to protect against moisture and shocks
Inpt Voltage: 220V AC
Phase: Single 1
Frecuency: 50hz – 60Hz
Output Voltage: 0V To 90V Dc Maximum
Current Max: 25A DC
Continuous 13A-Dc Excitation Current
Controls: Volt , Stab
Quick response ( 20 ms )
Thyristor Control Technology
Suitable for 10 KVA 1000 KVA Brushless Generator
Requires Only 2V-AC Residual Voltage to Buildup Alternator Voltage
Easy to Install
Low Cost
SKU: n/a
Boiler Controller, Flame Detector Card
DTA-9074 Burner Controller Unit Flame Rod Sensing
Safe start with DETECT FLAME ROD sensing technology
Custom timings setting for start & ignition & Main valve
work indication with led’s
Air Blower control
poilt & Main Valve control
Single or three trials for ignition
System diagnostic LED
Front panel mounting
APPLICATIONS
Gas furnaces
Boilers
Commercial cooking
Water heaters
SKU: n/a
Motion Sensor's, Sensor's
Infrared Motion Sensor Pir Body Sensor Switch Infrared Motion Sensor Detector for Led Lamp Home Garden 90~250VInfrared Motion Sensor Pir Body Sensor Switch Infrared Motion Sensor Detector for Led Lamp Home Garden 90~250V
Motion Sensor's, Sensor's
Infrared Motion Sensor Pir Body Sensor Switch Infrared Motion Sensor Detector for Led Lamp Home Garden 90~250VInfrared Motion Sensor Pir Body Sensor Switch Infrared Motion Sensor Detector for Led Lamp Home Garden 90~250V
Specifications:
Type: Sensor Switch
Material: ABS
Motion Angle: 180 Degree
Motion Distance: 2-8m / 6.6-26.2ft
Rotate Angle: 180 Degree
Working Voltage: 85-265V
Power: 30W
Waterproof: IP54
Installation Height: 1.8m- 2.5m / 5.9- 9.2ft
Work Temperature: -10 – 40 celsius
Work Humidity: Max 93%
Delay Time: 5+/-2 second – 4+/-1 min
Cable Length: 140mm / 5.5″
Item Size: 8*4.2*4cm / 3.1*1.7*1.6″(L*W*H)
Net Weight: 33g / 1.2oz
SKU: n/a
Electronic Components, HMI, LCD, PLC & HMI, Students Gallery
TJC4024T032_011R 3.2 inch USART HMI touch screen with GPU font picture configuration screen serial port TFT LCD screen
Electronic Components, HMI, LCD, PLC & HMI, Students Gallery
TJC4024T032_011R 3.2 inch USART HMI touch screen with GPU font picture configuration screen serial port TFT LCD screen
Resolution: 400*240
Serial port mode: 3.3V CMOS
Working voltage: 4.75-7V
Diagonal size of display area: 3.2 inch
Interface mode: 4pin_XH2.54
3.2 inch Nextion TFT HMI LCD Touchscreen NX8048K050 is a Seamless Human Machine Interface (HMI) solution. 3.2 inch Nextion TFT HMI LCD Touchscreen NX8048K050 that provides a control and visualization interface between a human and a process, machine, application or appliance. Nextion is mainly…
SKU: n/a
Battery Charger, Digital Battery Charger, Generator Battery Charger
DTA-4158 Battery Charger Digital 24V/30A & 24V/50A For Generator
Battery Charger, Digital Battery Charger, Generator Battery Charger
DTA-4158 Battery Charger Digital 24V/30A & 24V/50A For Generator
FEATURES
Model No: DTA-4158
Input Voltage: 180 t 270V AC
Out Voltage: 27.6V DC
Current: 50A
Digital Display for Volt and ampere.
Digital Display for Ampere
LEDBattery Status show
Short Circuit Protection With Fuse
2 Stage Charging for Continuous Connection.
Over Charge Protection
Over current Protection.
Low power consumption at no-load mode
Reverse Discharge Protection.
Two fans have been installed to keep the Battery Charger cool, which Automatically turns on during Heating
Easy to Install
Technology: Transformer Based
Ampere Metre On the Front Panel for Show Battery Charging Status
63A ampere switch is used for main power
100A ampere switch is used for the DC Output
The parameters are displayed on the front panel
Color: Red
Material: Copper Transformer and Metal Box
DTA-2450 is charger is capable of charging any type of battery attached to the generator
It automatically controls its amperes when the battery is fully charged
This charger has the capacity to charge batteries from 15 amps to 500×2 amps.
This charger is specially designed to slowly charge the continuous battery
This charger is made using high quality Parts and a 100% copper wire transformer
SKU: n/a
Battery Charger, Generator Battery Charger
DTA-4072 Battery Charger 24V/5A For Generator
FEATURES
Model No: DTA-4072
Input Voltage: 180 t 270V AC
Out Voltage: 27.6V DC
Current: 5A
Short Circuit Protection With Fuse
2 Stage Charging for Continuous Connection.
Over Charge Protection
Over current Protection.
Low power consumption at no-load mode
Reverse Discharge Protection.
Easy to Install
Technology: Transformer Based
Ampere Metre On the Front Panel for Show Battery Charging Status
Color: Red
Material: Copper Transformer and Metal Box
Size: Approx. 210mm x 155mm x 100mm
DTA-4059 is charger is capable of charging any type of battery attached to the generator
It automatically controls its amperes when the battery is fully charged
This charger has the capacity to charge batteries from 15 amps to 250×2 amps.
This charger is specially designed to slowly charge the continuous battery
This charger is made using high quality Parts and a 100% copper wire transformer
SKU: n/a
Boiler Controller, Water Pump Controller
DTA-11099 Water Level Switch For Boiler
Model No: DTA-11099
Input Voltage 220V
Rated Current: 12A Continuously
It Can be Installed Very Easily
2 Wirer Sensing
When the water touches the High level, the motor should stop
After leaving the high level, the Motor should turn on after the time
Microprocessor Based and very Efficient
SKU: n/a
Infrared Beam Active Sensor, Sensor's
ABO-20L Single Beam Detector Active Half Egg Beam Infrared Detector Photoelectric Sensor, Detect Distance: 20m
Infrared Beam Active Sensor, Sensor's
ABO-20L Single Beam Detector Active Half Egg Beam Infrared Detector Photoelectric Sensor, Detect Distance: 20m
| Item | Parameter |
| Model | ABL-20L |
|
Power supply
|
DC 10.5V–24V/0.5V
|
|
Maximum current
|
TX: 15mA MAX RX: 30mA MAX
|
|
Optical source
|
Infrared Pulse
|
|
Infrared wave length
|
940nm
|
|
Infrared transmission frequency
|
1.92KHz
|
|
Response speed
|
50ms
|
|
Alarm output time
|
≥1s
|
|
Detection mode
|
Block off the infrared beam
|
|
Infrared angle
|
<±10°
|
|
Infrared distance
|
≤20m
|
| Waterproof level | IP55 |
|
Relay contact capacity
|
AC,DC30V,0.5A max
|
|
Working environment
|
Temperature: -25°C-+55°C; Humidity: RH95%
|
|
Product dimension
|
76*49*29mm
|
SKU: n/a
Infrared Beam Active Sensor, Sensor's
IR Infrared Beam Sensor with 2 Beams Detector Outdoor Active (ABT-150)
Infrared Beam Active Sensor, Sensor's
IR Infrared Beam Sensor with 2 Beams Detector Outdoor Active (ABT-150)
Technical Specifications:
Response speed: 50 to 700m/sec adjustable
Alarm output: 1C relay contact output, contact capability DC30v/0.5A max
Power and voltage: DC12~24V, AC 11~18V
Working temperature: -25 ~ 55 degree C
Tamper output: 1B contact output, DC30V/0.5A max
Optical axis adjust angle(horizontal): 180° (± 90° )
Optical axis adjust angle(vertical): 20° (± 10° )
Weight: 300g for transmitter; 300g for receiver; 1000g for each pack (including bracket)
Valid length: 17CM
Response speed: 50 to 700m/sec adjustable
Alarm output: 1C relay contact output, contact capability DC30v/0.5A max
Power and voltage: DC12~24V, AC 11~18V
Working temperature: -25 ~ 55 degree C
Tamper output: 1B contact output, DC30V/0.5A max
Optical axis adjust angle(horizontal): 180° (± 90° )
Optical axis adjust angle(vertical): 20° (± 10° )
Weight: 300g for transmitter; 300g for receiver; 1000g for each pack (including bracket)
Valid length: 17CM
Application. Indoor, Outdoor
Transmission Mode.Cable
Receive Frequency.Wired
Indoor Detecting Distance.50-150m
Working Temperature.-25 Degree ~ 55 Degree
Wired or Wireless.Wired
Beams.2 Beams
Working Principle.Infrared– Relay Output
Alarm Volume (within 1m).Relay Output
Housing Color.Black
Outdoor Detecting Distance.50-150m
Valid Length.17cm
Relay Output.No or Nc
SKU: n/a
AMF / ATS Controller, Generator, Genset Starting Module
DTA-912 Digital Duel Fuel Control System
DTA-912 Digital Duel Fuel Control System
Microprocessor controled
Front panel mounting
Front panel programming
Ldc Display
Five Relay control card
Uses gas to reduce diesel consumption
As the load on the generator increases, the gas valve will open.
In case of low load, the valve will be shut down automatically.
Study the installation diagram for more information and to understand the card
SKU: n/a
DC Motor Drive, Motor Drive's
DTA-1514 DC Motor Drive 12V,24V 20A
FEATURES
Model No: DTA-1514
Input Voltage: 30v DC
Out Voltage: 2V to 24V DC
Current: 20A
Technology: PWM
Speed Control With Volume
Switch For Strat & Stop
Size: Approx. 100 x 95 x 40mm
Input Output Led Indicators
Easy to Install
SKU: n/a
AVR, Generator
DTA-226 Consealed AVR Automatic Voltage Regulator For Generator
feature keys
Model No DTA-226 Consealed
This model is specially designed to protect against moisture and shocks
Inpt Voltage: 220V AC
Phase: Single 1
Frecuency: 50hz – 60Hz
Output Voltage: 0V To 90V Dc Maximum
Current Max: 25A DC
Continuous 13A-Dc Excitation Current
Controls: Volt , Stab
Quick response ( 20 ms )
Thyristor Control Technology
Suitable for 10 KVA 1000 KVA Brushless Generator
Requires Only 2V-AC Residual Voltage to Buildup Alternator Voltage
Easy to Install
Low Cost
SKU: n/a
Boiler Controller, Flame Detector Card
DTA-9074 Burner Controller Unit Flame Rod Sensing
Safe start with DETECT FLAME ROD sensing technology
Custom timings setting for start & ignition & Main valve
work indication with led’s
Air Blower control
poilt & Main Valve control
Single or three trials for ignition
System diagnostic LED
Front panel mounting
APPLICATIONS
Gas furnaces
Boilers
Commercial cooking
Water heaters
SKU: n/a
Motion Sensor's, Sensor's
Infrared Motion Sensor Pir Body Sensor Switch Infrared Motion Sensor Detector for Led Lamp Home Garden 90~250VInfrared Motion Sensor Pir Body Sensor Switch Infrared Motion Sensor Detector for Led Lamp Home Garden 90~250V
Motion Sensor's, Sensor's
Infrared Motion Sensor Pir Body Sensor Switch Infrared Motion Sensor Detector for Led Lamp Home Garden 90~250VInfrared Motion Sensor Pir Body Sensor Switch Infrared Motion Sensor Detector for Led Lamp Home Garden 90~250V
Specifications:
Type: Sensor Switch
Material: ABS
Motion Angle: 180 Degree
Motion Distance: 2-8m / 6.6-26.2ft
Rotate Angle: 180 Degree
Working Voltage: 85-265V
Power: 30W
Waterproof: IP54
Installation Height: 1.8m- 2.5m / 5.9- 9.2ft
Work Temperature: -10 – 40 celsius
Work Humidity: Max 93%
Delay Time: 5+/-2 second – 4+/-1 min
Cable Length: 140mm / 5.5″
Item Size: 8*4.2*4cm / 3.1*1.7*1.6″(L*W*H)
Net Weight: 33g / 1.2oz
SKU: n/a
Electronic Components, HMI, LCD, PLC & HMI, Students Gallery
TJC4024T032_011R 3.2 inch USART HMI touch screen with GPU font picture configuration screen serial port TFT LCD screen
Electronic Components, HMI, LCD, PLC & HMI, Students Gallery
TJC4024T032_011R 3.2 inch USART HMI touch screen with GPU font picture configuration screen serial port TFT LCD screen
Resolution: 400*240
Serial port mode: 3.3V CMOS
Working voltage: 4.75-7V
Diagonal size of display area: 3.2 inch
Interface mode: 4pin_XH2.54
3.2 inch Nextion TFT HMI LCD Touchscreen NX8048K050 is a Seamless Human Machine Interface (HMI) solution. 3.2 inch Nextion TFT HMI LCD Touchscreen NX8048K050 that provides a control and visualization interface between a human and a process, machine, application or appliance. Nextion is mainly…
SKU: n/a
Battery Charger, Digital Battery Charger, Generator Battery Charger
DTA-4158 Battery Charger Digital 24V/30A & 24V/50A For Generator
Battery Charger, Digital Battery Charger, Generator Battery Charger
DTA-4158 Battery Charger Digital 24V/30A & 24V/50A For Generator
FEATURES
Model No: DTA-4158
Input Voltage: 180 t 270V AC
Out Voltage: 27.6V DC
Current: 50A
Digital Display for Volt and ampere.
Digital Display for Ampere
LEDBattery Status show
Short Circuit Protection With Fuse
2 Stage Charging for Continuous Connection.
Over Charge Protection
Over current Protection.
Low power consumption at no-load mode
Reverse Discharge Protection.
Two fans have been installed to keep the Battery Charger cool, which Automatically turns on during Heating
Easy to Install
Technology: Transformer Based
Ampere Metre On the Front Panel for Show Battery Charging Status
63A ampere switch is used for main power
100A ampere switch is used for the DC Output
The parameters are displayed on the front panel
Color: Red
Material: Copper Transformer and Metal Box
DTA-2450 is charger is capable of charging any type of battery attached to the generator
It automatically controls its amperes when the battery is fully charged
This charger has the capacity to charge batteries from 15 amps to 500×2 amps.
This charger is specially designed to slowly charge the continuous battery
This charger is made using high quality Parts and a 100% copper wire transformer
SKU: n/a
Battery Charger, Generator Battery Charger
DTA-4072 Battery Charger 24V/5A For Generator
FEATURES
Model No: DTA-4072
Input Voltage: 180 t 270V AC
Out Voltage: 27.6V DC
Current: 5A
Short Circuit Protection With Fuse
2 Stage Charging for Continuous Connection.
Over Charge Protection
Over current Protection.
Low power consumption at no-load mode
Reverse Discharge Protection.
Easy to Install
Technology: Transformer Based
Ampere Metre On the Front Panel for Show Battery Charging Status
Color: Red
Material: Copper Transformer and Metal Box
Size: Approx. 210mm x 155mm x 100mm
DTA-4059 is charger is capable of charging any type of battery attached to the generator
It automatically controls its amperes when the battery is fully charged
This charger has the capacity to charge batteries from 15 amps to 250×2 amps.
This charger is specially designed to slowly charge the continuous battery
This charger is made using high quality Parts and a 100% copper wire transformer
SKU: n/a
Boiler Controller, Water Pump Controller
DTA-11099 Water Level Switch For Boiler
Model No: DTA-11099
Input Voltage 220V
Rated Current: 12A Continuously
It Can be Installed Very Easily
2 Wirer Sensing
When the water touches the High level, the motor should stop
After leaving the high level, the Motor should turn on after the time
Microprocessor Based and very Efficient
SKU: n/a
Infrared Beam Active Sensor, Sensor's
ABO-20L Single Beam Detector Active Half Egg Beam Infrared Detector Photoelectric Sensor, Detect Distance: 20m
Infrared Beam Active Sensor, Sensor's
ABO-20L Single Beam Detector Active Half Egg Beam Infrared Detector Photoelectric Sensor, Detect Distance: 20m
| Item | Parameter |
| Model | ABL-20L |
|
Power supply
|
DC 10.5V–24V/0.5V
|
|
Maximum current
|
TX: 15mA MAX RX: 30mA MAX
|
|
Optical source
|
Infrared Pulse
|
|
Infrared wave length
|
940nm
|
|
Infrared transmission frequency
|
1.92KHz
|
|
Response speed
|
50ms
|
|
Alarm output time
|
≥1s
|
|
Detection mode
|
Block off the infrared beam
|
|
Infrared angle
|
<±10°
|
|
Infrared distance
|
≤20m
|
| Waterproof level | IP55 |
|
Relay contact capacity
|
AC,DC30V,0.5A max
|
|
Working environment
|
Temperature: -25°C-+55°C; Humidity: RH95%
|
|
Product dimension
|
76*49*29mm
|
SKU: n/a
Infrared Beam Active Sensor, Sensor's
IR Infrared Beam Sensor with 2 Beams Detector Outdoor Active (ABT-150)
Infrared Beam Active Sensor, Sensor's
IR Infrared Beam Sensor with 2 Beams Detector Outdoor Active (ABT-150)
Technical Specifications:
Response speed: 50 to 700m/sec adjustable
Alarm output: 1C relay contact output, contact capability DC30v/0.5A max
Power and voltage: DC12~24V, AC 11~18V
Working temperature: -25 ~ 55 degree C
Tamper output: 1B contact output, DC30V/0.5A max
Optical axis adjust angle(horizontal): 180° (± 90° )
Optical axis adjust angle(vertical): 20° (± 10° )
Weight: 300g for transmitter; 300g for receiver; 1000g for each pack (including bracket)
Valid length: 17CM
Response speed: 50 to 700m/sec adjustable
Alarm output: 1C relay contact output, contact capability DC30v/0.5A max
Power and voltage: DC12~24V, AC 11~18V
Working temperature: -25 ~ 55 degree C
Tamper output: 1B contact output, DC30V/0.5A max
Optical axis adjust angle(horizontal): 180° (± 90° )
Optical axis adjust angle(vertical): 20° (± 10° )
Weight: 300g for transmitter; 300g for receiver; 1000g for each pack (including bracket)
Valid length: 17CM
Application. Indoor, Outdoor
Transmission Mode.Cable
Receive Frequency.Wired
Indoor Detecting Distance.50-150m
Working Temperature.-25 Degree ~ 55 Degree
Wired or Wireless.Wired
Beams.2 Beams
Working Principle.Infrared– Relay Output
Alarm Volume (within 1m).Relay Output
Housing Color.Black
Outdoor Detecting Distance.50-150m
Valid Length.17cm
Relay Output.No or Nc
SKU: n/a
AMF / ATS Controller, Generator, Genset Starting Module
DTA-912 Digital Duel Fuel Control System
DTA-912 Digital Duel Fuel Control System
Microprocessor controled
Front panel mounting
Front panel programming
Ldc Display
Five Relay control card
Uses gas to reduce diesel consumption
As the load on the generator increases, the gas valve will open.
In case of low load, the valve will be shut down automatically.
Study the installation diagram for more information and to understand the card
SKU: n/a
DC Motor Drive, Motor Drive's
DTA-1514 DC Motor Drive 12V,24V 20A
FEATURES
Model No: DTA-1514
Input Voltage: 30v DC
Out Voltage: 2V to 24V DC
Current: 20A
Technology: PWM
Speed Control With Volume
Switch For Strat & Stop
Size: Approx. 100 x 95 x 40mm
Input Output Led Indicators
Easy to Install
SKU: n/a
AVR, Generator
DTA-226 Consealed AVR Automatic Voltage Regulator For Generator
feature keys
Model No DTA-226 Consealed
This model is specially designed to protect against moisture and shocks
Inpt Voltage: 220V AC
Phase: Single 1
Frecuency: 50hz – 60Hz
Output Voltage: 0V To 90V Dc Maximum
Current Max: 25A DC
Continuous 13A-Dc Excitation Current
Controls: Volt , Stab
Quick response ( 20 ms )
Thyristor Control Technology
Suitable for 10 KVA 1000 KVA Brushless Generator
Requires Only 2V-AC Residual Voltage to Buildup Alternator Voltage
Easy to Install
Low Cost
SKU: n/a
Boiler Controller, Flame Detector Card
DTA-9074 Burner Controller Unit Flame Rod Sensing
Safe start with DETECT FLAME ROD sensing technology
Custom timings setting for start & ignition & Main valve
work indication with led’s
Air Blower control
poilt & Main Valve control
Single or three trials for ignition
System diagnostic LED
Front panel mounting
APPLICATIONS
Gas furnaces
Boilers
Commercial cooking
Water heaters
SKU: n/a
Motion Sensor's, Sensor's
Infrared Motion Sensor Pir Body Sensor Switch Infrared Motion Sensor Detector for Led Lamp Home Garden 90~250VInfrared Motion Sensor Pir Body Sensor Switch Infrared Motion Sensor Detector for Led Lamp Home Garden 90~250V
Motion Sensor's, Sensor's
Infrared Motion Sensor Pir Body Sensor Switch Infrared Motion Sensor Detector for Led Lamp Home Garden 90~250VInfrared Motion Sensor Pir Body Sensor Switch Infrared Motion Sensor Detector for Led Lamp Home Garden 90~250V
Specifications:
Type: Sensor Switch
Material: ABS
Motion Angle: 180 Degree
Motion Distance: 2-8m / 6.6-26.2ft
Rotate Angle: 180 Degree
Working Voltage: 85-265V
Power: 30W
Waterproof: IP54
Installation Height: 1.8m- 2.5m / 5.9- 9.2ft
Work Temperature: -10 – 40 celsius
Work Humidity: Max 93%
Delay Time: 5+/-2 second – 4+/-1 min
Cable Length: 140mm / 5.5″
Item Size: 8*4.2*4cm / 3.1*1.7*1.6″(L*W*H)
Net Weight: 33g / 1.2oz
SKU: n/a
Electronic Components, HMI, LCD, PLC & HMI, Students Gallery
TJC4024T032_011R 3.2 inch USART HMI touch screen with GPU font picture configuration screen serial port TFT LCD screen
Electronic Components, HMI, LCD, PLC & HMI, Students Gallery
TJC4024T032_011R 3.2 inch USART HMI touch screen with GPU font picture configuration screen serial port TFT LCD screen
Resolution: 400*240
Serial port mode: 3.3V CMOS
Working voltage: 4.75-7V
Diagonal size of display area: 3.2 inch
Interface mode: 4pin_XH2.54
3.2 inch Nextion TFT HMI LCD Touchscreen NX8048K050 is a Seamless Human Machine Interface (HMI) solution. 3.2 inch Nextion TFT HMI LCD Touchscreen NX8048K050 that provides a control and visualization interface between a human and a process, machine, application or appliance. Nextion is mainly…
SKU: n/a
Battery Charger, Digital Battery Charger, Generator Battery Charger
DTA-4158 Battery Charger Digital 24V/30A & 24V/50A For Generator
Battery Charger, Digital Battery Charger, Generator Battery Charger
DTA-4158 Battery Charger Digital 24V/30A & 24V/50A For Generator
FEATURES
Model No: DTA-4158
Input Voltage: 180 t 270V AC
Out Voltage: 27.6V DC
Current: 50A
Digital Display for Volt and ampere.
Digital Display for Ampere
LEDBattery Status show
Short Circuit Protection With Fuse
2 Stage Charging for Continuous Connection.
Over Charge Protection
Over current Protection.
Low power consumption at no-load mode
Reverse Discharge Protection.
Two fans have been installed to keep the Battery Charger cool, which Automatically turns on during Heating
Easy to Install
Technology: Transformer Based
Ampere Metre On the Front Panel for Show Battery Charging Status
63A ampere switch is used for main power
100A ampere switch is used for the DC Output
The parameters are displayed on the front panel
Color: Red
Material: Copper Transformer and Metal Box
DTA-2450 is charger is capable of charging any type of battery attached to the generator
It automatically controls its amperes when the battery is fully charged
This charger has the capacity to charge batteries from 15 amps to 500×2 amps.
This charger is specially designed to slowly charge the continuous battery
This charger is made using high quality Parts and a 100% copper wire transformer
SKU: n/a
Battery Charger, Generator Battery Charger
DTA-4072 Battery Charger 24V/5A For Generator
FEATURES
Model No: DTA-4072
Input Voltage: 180 t 270V AC
Out Voltage: 27.6V DC
Current: 5A
Short Circuit Protection With Fuse
2 Stage Charging for Continuous Connection.
Over Charge Protection
Over current Protection.
Low power consumption at no-load mode
Reverse Discharge Protection.
Easy to Install
Technology: Transformer Based
Ampere Metre On the Front Panel for Show Battery Charging Status
Color: Red
Material: Copper Transformer and Metal Box
Size: Approx. 210mm x 155mm x 100mm
DTA-4059 is charger is capable of charging any type of battery attached to the generator
It automatically controls its amperes when the battery is fully charged
This charger has the capacity to charge batteries from 15 amps to 250×2 amps.
This charger is specially designed to slowly charge the continuous battery
This charger is made using high quality Parts and a 100% copper wire transformer
SKU: n/a
Boiler Controller, Water Pump Controller
DTA-11099 Water Level Switch For Boiler
Model No: DTA-11099
Input Voltage 220V
Rated Current: 12A Continuously
It Can be Installed Very Easily
2 Wirer Sensing
When the water touches the High level, the motor should stop
After leaving the high level, the Motor should turn on after the time
Microprocessor Based and very Efficient
SKU: n/a
Infrared Beam Active Sensor, Sensor's
ABO-20L Single Beam Detector Active Half Egg Beam Infrared Detector Photoelectric Sensor, Detect Distance: 20m
Infrared Beam Active Sensor, Sensor's
ABO-20L Single Beam Detector Active Half Egg Beam Infrared Detector Photoelectric Sensor, Detect Distance: 20m
| Item | Parameter |
| Model | ABL-20L |
|
Power supply
|
DC 10.5V–24V/0.5V
|
|
Maximum current
|
TX: 15mA MAX RX: 30mA MAX
|
|
Optical source
|
Infrared Pulse
|
|
Infrared wave length
|
940nm
|
|
Infrared transmission frequency
|
1.92KHz
|
|
Response speed
|
50ms
|
|
Alarm output time
|
≥1s
|
|
Detection mode
|
Block off the infrared beam
|
|
Infrared angle
|
<±10°
|
|
Infrared distance
|
≤20m
|
| Waterproof level | IP55 |
|
Relay contact capacity
|
AC,DC30V,0.5A max
|
|
Working environment
|
Temperature: -25°C-+55°C; Humidity: RH95%
|
|
Product dimension
|
76*49*29mm
|
SKU: n/a
Infrared Beam Active Sensor, Sensor's
IR Infrared Beam Sensor with 2 Beams Detector Outdoor Active (ABT-150)
Infrared Beam Active Sensor, Sensor's
IR Infrared Beam Sensor with 2 Beams Detector Outdoor Active (ABT-150)
Technical Specifications:
Response speed: 50 to 700m/sec adjustable
Alarm output: 1C relay contact output, contact capability DC30v/0.5A max
Power and voltage: DC12~24V, AC 11~18V
Working temperature: -25 ~ 55 degree C
Tamper output: 1B contact output, DC30V/0.5A max
Optical axis adjust angle(horizontal): 180° (± 90° )
Optical axis adjust angle(vertical): 20° (± 10° )
Weight: 300g for transmitter; 300g for receiver; 1000g for each pack (including bracket)
Valid length: 17CM
Response speed: 50 to 700m/sec adjustable
Alarm output: 1C relay contact output, contact capability DC30v/0.5A max
Power and voltage: DC12~24V, AC 11~18V
Working temperature: -25 ~ 55 degree C
Tamper output: 1B contact output, DC30V/0.5A max
Optical axis adjust angle(horizontal): 180° (± 90° )
Optical axis adjust angle(vertical): 20° (± 10° )
Weight: 300g for transmitter; 300g for receiver; 1000g for each pack (including bracket)
Valid length: 17CM
Application. Indoor, Outdoor
Transmission Mode.Cable
Receive Frequency.Wired
Indoor Detecting Distance.50-150m
Working Temperature.-25 Degree ~ 55 Degree
Wired or Wireless.Wired
Beams.2 Beams
Working Principle.Infrared– Relay Output
Alarm Volume (within 1m).Relay Output
Housing Color.Black
Outdoor Detecting Distance.50-150m
Valid Length.17cm
Relay Output.No or Nc
SKU: n/a
Bestsellers
Laptops & Computers
Automatic Day Night Sensor, Sensor's
12DC Automatic Light Control Sun Switch 10A Photosensor Photocell Sensor
Automatic Day Night Sensor, Sensor's
12DC Automatic Light Control Sun Switch 10A Photosensor Photocell Sensor
Working Voltage: 12V DC
Rated Current: 10A
Operating Temperature: -20C – +50C
Power Consumption: 0.5W Max.
Fixing Hole Diameter: 4.9mm / 0.2″;Size : 3.3 x 4.2 x 5cm / 1.3″ x 1.7″ x 2″(L*W*H)
External Material: Plastic
Color: White, Blue
SKU: n/a
Motion Sensor's, Sensor's
360 Degree PIR Motion Movement Sensor Switch 220-240V 1200W Time and LUX Adjustable Light Switch for LED Lights White
Motion Sensor's, Sensor's
360 Degree PIR Motion Movement Sensor Switch 220-240V 1200W Time and LUX Adjustable Light Switch for LED Lights White
Product Description
Quality control standard
360 Degree Ceiling Mount PIR Motion-Sensor Lamp
Operating volt: ac 220-250v 50hz-60hz.
Load power: upto 300/1200w max
Ambient light: 3-2000 (adjuestable)
Load type: incandescent lamp, led light, clf, fans, etc
Detecting distance: 0~7m
Detecting angle: 360 degree.
Installtion hight: 2.2-4 mtr
Motion detetion speed: 0.6~1m/s
Power cusumption: 0.1w (static) & 0.4(work)
Working humidity: less than 93%rh
Delay: 10 seconds -7 minutes (adjustable)
SKU: n/a
Motion Sensor's, Sensor's
40mm AC 220V Infrared PIR Motion Sensor Automatically Light On Off Sensor
Specifications:
Type: PIR Switch
Color: White
Working Voltage/Frequency:AC100-240V, 50/60Hz
Output power : ≤40W
Photo sensing Setting:≤2Lux, ≤25Lux, 2000Lux
Sensing Distance: 4-6m
Time delaya djustment :15secs 45secs 5mins
Angle Coverage: 110°
Extreme Temperature Using:-10°—+45°
Stand by power consumption:<0.1W
Size:45 mmx 40mm x 25mm
Package Contents:
1 x PIR Motion SensorSwitch
SKU: n/a
Infrared Beam Active Sensor, Sensor's
ABO-20L Single Beam Detector Active Half Egg Beam Infrared Detector Photoelectric Sensor, Detect Distance: 20m
Infrared Beam Active Sensor, Sensor's
ABO-20L Single Beam Detector Active Half Egg Beam Infrared Detector Photoelectric Sensor, Detect Distance: 20m
| Item | Parameter |
| Model | ABL-20L |
|
Power supply
|
DC 10.5V–24V/0.5V
|
|
Maximum current
|
TX: 15mA MAX RX: 30mA MAX
|
|
Optical source
|
Infrared Pulse
|
|
Infrared wave length
|
940nm
|
|
Infrared transmission frequency
|
1.92KHz
|
|
Response speed
|
50ms
|
|
Alarm output time
|
≥1s
|
|
Detection mode
|
Block off the infrared beam
|
|
Infrared angle
|
<±10°
|
|
Infrared distance
|
≤20m
|
| Waterproof level | IP55 |
|
Relay contact capacity
|
AC,DC30V,0.5A max
|
|
Working environment
|
Temperature: -25°C-+55°C; Humidity: RH95%
|
|
Product dimension
|
76*49*29mm
|
SKU: n/a
Different Types Of Sensor's, Sensor's
Aosong original AM2302 Digital Temperature Sensor / Humidity Sensor For Arduino DHT22
Different Types Of Sensor's, Sensor's
Aosong original AM2302 Digital Temperature Sensor / Humidity Sensor For Arduino DHT22
The DHT22 combined temperature and relative humidity sensor provides a simple and low-cost solution.
To differentiate between the two readings, the DHT22 makes use of a simple protocol on a single data pin which is best interpreted by using existing library code. The instructions below show how to connect the DHT22 up to your Particle Argon, and take you through the process of finding and including the right library in your application code using the Web IDE.
This example is based on the Adafruit version that is provided with the library code, and the Photon Maker Kit tutorial linked in the box above.
SKU: n/a
Uncategorized
AVR R250 Automatic Voltage Regulator Controls Module Card For Leroy SomerAVR R250 Automatic Voltage Regulator Controls Module Card For Leroy Somer
Uncategorized
AVR R250 Automatic Voltage Regulator Controls Module Card For Leroy SomerAVR R250 Automatic Voltage Regulator Controls Module Card For Leroy Somer
| Description:
Condition: 100% new Material: Metal & plastic Package included: 1 pc AVR Application(just for reference): AVR R250 NEW Automatic Voltage Regulator AVR Controls Module Card R250 For Leroy Somer Technical specification: Voltage regulation: around +/-0.5% Voltage supply/sensing range 85 to 139 V (50/60Hz) Rapid response time (500ms) for a transient voltage variation amplitude of +/-20% Voltage setting p1 Stability setting p2 Supply protected with an 8A fuse, slow action(supports 10A for 10s) |
SKU: n/a
AMF / ATS Controller, Generator, Genset Starting Module
DKG105 DATAKOM Generator Automatic Mains Failure control panel
AMF / ATS Controller, Generator, Genset Starting Module
DKG105 DATAKOM Generator Automatic Mains Failure control panel
DKG-105 AUTOMATIC MAINS FAILURE UNIT
The DKG-105 automatic mains failure unit is a microprocessor based digital unit offering all functions needed for the automatic control of a genset.
The unit fits into a standard 72x72mm panel meter opening and offers a very cost effective and
space saving solution for the basic genset control.
In automatic mode, the unit monitors 3 phases of the mains voltage and controls the automatic starting, stopping and load transfer of the generator.
Once the generator is running, the device monitors the internal protections and external fault inputs.
DKG-105 provides a full set of digitally adjustable timers and threshold levels. Also the relay configuration is programmable, enabling the control of various types of engines, including gasoline engines.
The programs may be modified by the customer via pushbuttons on the unit, and do not require an external unit.
| Automatic engine starting and stopping
Gas engine support Automatic mains failure monitoring Automatic load transfer Automatic shutdown on fault condition Test mode available Survives cranking dropouts Digital engine run-hours display Provision for energize to stop, preheat & choke outputs Mains phases voltage limits checking Generator phase voltage limits checking |
SKU: n/a
AMF / ATS Controller, Generator, Genset Starting Module
DSE 704 Auto Start Generator Control Panel Alternator
AMF / ATS Controller, Generator, Genset Starting Module
DSE 704 Auto Start Generator Control Panel Alternator
Features:
The automatic (utility) sector provides monitoring
Automatic shutdown when fault conditions are detected
Manual start
Engine preheating
Motor monitoring and protection functions
Protected semiconductor outputs (PSS)
Front panel mounting
Front panel programming
Tamper-proof engine hour counter
Remote start
LED indicators
Configurable timers
Configurable outputs
Single-phase / three-phase hand detection
SKU: n/a
Smartphones
Automatic Day Night Sensor, Sensor's
12DC Automatic Light Control Sun Switch 10A Photosensor Photocell Sensor
Automatic Day Night Sensor, Sensor's
12DC Automatic Light Control Sun Switch 10A Photosensor Photocell Sensor
Working Voltage: 12V DC
Rated Current: 10A
Operating Temperature: -20C – +50C
Power Consumption: 0.5W Max.
Fixing Hole Diameter: 4.9mm / 0.2″;Size : 3.3 x 4.2 x 5cm / 1.3″ x 1.7″ x 2″(L*W*H)
External Material: Plastic
Color: White, Blue
SKU: n/a
Motion Sensor's, Sensor's
360 Degree PIR Motion Movement Sensor Switch 220-240V 1200W Time and LUX Adjustable Light Switch for LED Lights White
Motion Sensor's, Sensor's
360 Degree PIR Motion Movement Sensor Switch 220-240V 1200W Time and LUX Adjustable Light Switch for LED Lights White
Product Description
Quality control standard
360 Degree Ceiling Mount PIR Motion-Sensor Lamp
Operating volt: ac 220-250v 50hz-60hz.
Load power: upto 300/1200w max
Ambient light: 3-2000 (adjuestable)
Load type: incandescent lamp, led light, clf, fans, etc
Detecting distance: 0~7m
Detecting angle: 360 degree.
Installtion hight: 2.2-4 mtr
Motion detetion speed: 0.6~1m/s
Power cusumption: 0.1w (static) & 0.4(work)
Working humidity: less than 93%rh
Delay: 10 seconds -7 minutes (adjustable)
SKU: n/a
Motion Sensor's, Sensor's
40mm AC 220V Infrared PIR Motion Sensor Automatically Light On Off Sensor
Specifications:
Type: PIR Switch
Color: White
Working Voltage/Frequency:AC100-240V, 50/60Hz
Output power : ≤40W
Photo sensing Setting:≤2Lux, ≤25Lux, 2000Lux
Sensing Distance: 4-6m
Time delaya djustment :15secs 45secs 5mins
Angle Coverage: 110°
Extreme Temperature Using:-10°—+45°
Stand by power consumption:<0.1W
Size:45 mmx 40mm x 25mm
Package Contents:
1 x PIR Motion SensorSwitch
SKU: n/a
Infrared Beam Active Sensor, Sensor's
ABO-20L Single Beam Detector Active Half Egg Beam Infrared Detector Photoelectric Sensor, Detect Distance: 20m
Infrared Beam Active Sensor, Sensor's
ABO-20L Single Beam Detector Active Half Egg Beam Infrared Detector Photoelectric Sensor, Detect Distance: 20m
| Item | Parameter |
| Model | ABL-20L |
|
Power supply
|
DC 10.5V–24V/0.5V
|
|
Maximum current
|
TX: 15mA MAX RX: 30mA MAX
|
|
Optical source
|
Infrared Pulse
|
|
Infrared wave length
|
940nm
|
|
Infrared transmission frequency
|
1.92KHz
|
|
Response speed
|
50ms
|
|
Alarm output time
|
≥1s
|
|
Detection mode
|
Block off the infrared beam
|
|
Infrared angle
|
<±10°
|
|
Infrared distance
|
≤20m
|
| Waterproof level | IP55 |
|
Relay contact capacity
|
AC,DC30V,0.5A max
|
|
Working environment
|
Temperature: -25°C-+55°C; Humidity: RH95%
|
|
Product dimension
|
76*49*29mm
|
SKU: n/a
Different Types Of Sensor's, Sensor's
Aosong original AM2302 Digital Temperature Sensor / Humidity Sensor For Arduino DHT22
Different Types Of Sensor's, Sensor's
Aosong original AM2302 Digital Temperature Sensor / Humidity Sensor For Arduino DHT22
The DHT22 combined temperature and relative humidity sensor provides a simple and low-cost solution.
To differentiate between the two readings, the DHT22 makes use of a simple protocol on a single data pin which is best interpreted by using existing library code. The instructions below show how to connect the DHT22 up to your Particle Argon, and take you through the process of finding and including the right library in your application code using the Web IDE.
This example is based on the Adafruit version that is provided with the library code, and the Photon Maker Kit tutorial linked in the box above.
SKU: n/a
Uncategorized
AVR R250 Automatic Voltage Regulator Controls Module Card For Leroy SomerAVR R250 Automatic Voltage Regulator Controls Module Card For Leroy Somer
Uncategorized
AVR R250 Automatic Voltage Regulator Controls Module Card For Leroy SomerAVR R250 Automatic Voltage Regulator Controls Module Card For Leroy Somer
| Description:
Condition: 100% new Material: Metal & plastic Package included: 1 pc AVR Application(just for reference): AVR R250 NEW Automatic Voltage Regulator AVR Controls Module Card R250 For Leroy Somer Technical specification: Voltage regulation: around +/-0.5% Voltage supply/sensing range 85 to 139 V (50/60Hz) Rapid response time (500ms) for a transient voltage variation amplitude of +/-20% Voltage setting p1 Stability setting p2 Supply protected with an 8A fuse, slow action(supports 10A for 10s) |
SKU: n/a
AMF / ATS Controller, Generator, Genset Starting Module
DKG105 DATAKOM Generator Automatic Mains Failure control panel
AMF / ATS Controller, Generator, Genset Starting Module
DKG105 DATAKOM Generator Automatic Mains Failure control panel
DKG-105 AUTOMATIC MAINS FAILURE UNIT
The DKG-105 automatic mains failure unit is a microprocessor based digital unit offering all functions needed for the automatic control of a genset.
The unit fits into a standard 72x72mm panel meter opening and offers a very cost effective and
space saving solution for the basic genset control.
In automatic mode, the unit monitors 3 phases of the mains voltage and controls the automatic starting, stopping and load transfer of the generator.
Once the generator is running, the device monitors the internal protections and external fault inputs.
DKG-105 provides a full set of digitally adjustable timers and threshold levels. Also the relay configuration is programmable, enabling the control of various types of engines, including gasoline engines.
The programs may be modified by the customer via pushbuttons on the unit, and do not require an external unit.
| Automatic engine starting and stopping
Gas engine support Automatic mains failure monitoring Automatic load transfer Automatic shutdown on fault condition Test mode available Survives cranking dropouts Digital engine run-hours display Provision for energize to stop, preheat & choke outputs Mains phases voltage limits checking Generator phase voltage limits checking |
SKU: n/a
AMF / ATS Controller, Generator, Genset Starting Module
DSE 704 Auto Start Generator Control Panel Alternator
AMF / ATS Controller, Generator, Genset Starting Module
DSE 704 Auto Start Generator Control Panel Alternator
Features:
The automatic (utility) sector provides monitoring
Automatic shutdown when fault conditions are detected
Manual start
Engine preheating
Motor monitoring and protection functions
Protected semiconductor outputs (PSS)
Front panel mounting
Front panel programming
Tamper-proof engine hour counter
Remote start
LED indicators
Configurable timers
Configurable outputs
Single-phase / three-phase hand detection
SKU: n/a
Recently Viewed
Automatic Day Night Sensor, Sensor's
12DC Automatic Light Control Sun Switch 10A Photosensor Photocell Sensor
Automatic Day Night Sensor, Sensor's
12DC Automatic Light Control Sun Switch 10A Photosensor Photocell Sensor
Working Voltage: 12V DC
Rated Current: 10A
Operating Temperature: -20C – +50C
Power Consumption: 0.5W Max.
Fixing Hole Diameter: 4.9mm / 0.2″;Size : 3.3 x 4.2 x 5cm / 1.3″ x 1.7″ x 2″(L*W*H)
External Material: Plastic
Color: White, Blue
SKU: n/a
Motion Sensor's, Sensor's
360 Degree PIR Motion Movement Sensor Switch 220-240V 1200W Time and LUX Adjustable Light Switch for LED Lights White
Motion Sensor's, Sensor's
360 Degree PIR Motion Movement Sensor Switch 220-240V 1200W Time and LUX Adjustable Light Switch for LED Lights White
Product Description
Quality control standard
360 Degree Ceiling Mount PIR Motion-Sensor Lamp
Operating volt: ac 220-250v 50hz-60hz.
Load power: upto 300/1200w max
Ambient light: 3-2000 (adjuestable)
Load type: incandescent lamp, led light, clf, fans, etc
Detecting distance: 0~7m
Detecting angle: 360 degree.
Installtion hight: 2.2-4 mtr
Motion detetion speed: 0.6~1m/s
Power cusumption: 0.1w (static) & 0.4(work)
Working humidity: less than 93%rh
Delay: 10 seconds -7 minutes (adjustable)
SKU: n/a
Motion Sensor's, Sensor's
40mm AC 220V Infrared PIR Motion Sensor Automatically Light On Off Sensor
Specifications:
Type: PIR Switch
Color: White
Working Voltage/Frequency:AC100-240V, 50/60Hz
Output power : ≤40W
Photo sensing Setting:≤2Lux, ≤25Lux, 2000Lux
Sensing Distance: 4-6m
Time delaya djustment :15secs 45secs 5mins
Angle Coverage: 110°
Extreme Temperature Using:-10°—+45°
Stand by power consumption:<0.1W
Size:45 mmx 40mm x 25mm
Package Contents:
1 x PIR Motion SensorSwitch
SKU: n/a
Infrared Beam Active Sensor, Sensor's
ABO-20L Single Beam Detector Active Half Egg Beam Infrared Detector Photoelectric Sensor, Detect Distance: 20m
Infrared Beam Active Sensor, Sensor's
ABO-20L Single Beam Detector Active Half Egg Beam Infrared Detector Photoelectric Sensor, Detect Distance: 20m
| Item | Parameter |
| Model | ABL-20L |
|
Power supply
|
DC 10.5V–24V/0.5V
|
|
Maximum current
|
TX: 15mA MAX RX: 30mA MAX
|
|
Optical source
|
Infrared Pulse
|
|
Infrared wave length
|
940nm
|
|
Infrared transmission frequency
|
1.92KHz
|
|
Response speed
|
50ms
|
|
Alarm output time
|
≥1s
|
|
Detection mode
|
Block off the infrared beam
|
|
Infrared angle
|
<±10°
|
|
Infrared distance
|
≤20m
|
| Waterproof level | IP55 |
|
Relay contact capacity
|
AC,DC30V,0.5A max
|
|
Working environment
|
Temperature: -25°C-+55°C; Humidity: RH95%
|
|
Product dimension
|
76*49*29mm
|
SKU: n/a
Different Types Of Sensor's, Sensor's
Aosong original AM2302 Digital Temperature Sensor / Humidity Sensor For Arduino DHT22
Different Types Of Sensor's, Sensor's
Aosong original AM2302 Digital Temperature Sensor / Humidity Sensor For Arduino DHT22
The DHT22 combined temperature and relative humidity sensor provides a simple and low-cost solution.
To differentiate between the two readings, the DHT22 makes use of a simple protocol on a single data pin which is best interpreted by using existing library code. The instructions below show how to connect the DHT22 up to your Particle Argon, and take you through the process of finding and including the right library in your application code using the Web IDE.
This example is based on the Adafruit version that is provided with the library code, and the Photon Maker Kit tutorial linked in the box above.
SKU: n/a
Uncategorized
AVR R250 Automatic Voltage Regulator Controls Module Card For Leroy SomerAVR R250 Automatic Voltage Regulator Controls Module Card For Leroy Somer
Uncategorized
AVR R250 Automatic Voltage Regulator Controls Module Card For Leroy SomerAVR R250 Automatic Voltage Regulator Controls Module Card For Leroy Somer
| Description:
Condition: 100% new Material: Metal & plastic Package included: 1 pc AVR Application(just for reference): AVR R250 NEW Automatic Voltage Regulator AVR Controls Module Card R250 For Leroy Somer Technical specification: Voltage regulation: around +/-0.5% Voltage supply/sensing range 85 to 139 V (50/60Hz) Rapid response time (500ms) for a transient voltage variation amplitude of +/-20% Voltage setting p1 Stability setting p2 Supply protected with an 8A fuse, slow action(supports 10A for 10s) |
SKU: n/a
AMF / ATS Controller, Generator, Genset Starting Module
DKG105 DATAKOM Generator Automatic Mains Failure control panel
AMF / ATS Controller, Generator, Genset Starting Module
DKG105 DATAKOM Generator Automatic Mains Failure control panel
DKG-105 AUTOMATIC MAINS FAILURE UNIT
The DKG-105 automatic mains failure unit is a microprocessor based digital unit offering all functions needed for the automatic control of a genset.
The unit fits into a standard 72x72mm panel meter opening and offers a very cost effective and
space saving solution for the basic genset control.
In automatic mode, the unit monitors 3 phases of the mains voltage and controls the automatic starting, stopping and load transfer of the generator.
Once the generator is running, the device monitors the internal protections and external fault inputs.
DKG-105 provides a full set of digitally adjustable timers and threshold levels. Also the relay configuration is programmable, enabling the control of various types of engines, including gasoline engines.
The programs may be modified by the customer via pushbuttons on the unit, and do not require an external unit.
| Automatic engine starting and stopping
Gas engine support Automatic mains failure monitoring Automatic load transfer Automatic shutdown on fault condition Test mode available Survives cranking dropouts Digital engine run-hours display Provision for energize to stop, preheat & choke outputs Mains phases voltage limits checking Generator phase voltage limits checking |
SKU: n/a
AMF / ATS Controller, Generator, Genset Starting Module
DSE 704 Auto Start Generator Control Panel Alternator
AMF / ATS Controller, Generator, Genset Starting Module
DSE 704 Auto Start Generator Control Panel Alternator
Features:
The automatic (utility) sector provides monitoring
Automatic shutdown when fault conditions are detected
Manual start
Engine preheating
Motor monitoring and protection functions
Protected semiconductor outputs (PSS)
Front panel mounting
Front panel programming
Tamper-proof engine hour counter
Remote start
LED indicators
Configurable timers
Configurable outputs
Single-phase / three-phase hand detection
SKU: n/a