DTA-264 Generator AMF/ATS Control Module With Heater & Low Oil Pressure & High Temperature, Low High Voltage, Over Under frequency Safety
- Auto Main Failure and Automatic load transfer With Safety
- Microprocessor controled
- Manual start Optional
- Front panel mounting
- Front panel programming
- Configurable timers
- Ldc Display
- Main Shutdown timer
- Heater On Timer
- Crank On Timer
- Crank Rest Timer
- Generator on Load Timer
- Size : 165mm , 125mm , 45 mm
- Penal Cutout Size: 113mm X 152mm
- Generator Off Load Timer
- Main On Load Timer
- Generator Cooling Timer
- Choke On Timer
- Frecuency Delay Timer
- Frecuency High Limit
- Frecuency Lower Limit
- Warmup Timer
- Numebr of Start Attempts
- Main Voltage High Limit
- Main Voltage Lower Limit
- Generator Over Voltage high Limit
- Generator Under Voltage Limit
- DC Supply: 12V & 24volts, (+) and (-) terminals.
₨10,000
Based on 0 reviews
Be the first to review “DTA-264 Generator AMF/ATS Control Module With Heater & Low Oil Pressure & High Temperature, Low High Voltage, Over Under frequency Safety”
Related products
-
AVR, Generator
GAVR-12A GAVR 12A AVR for Generator Automatic Voltage
TECHNICAL DATA:
Voltage Set-up:The voltage set up when the remnant magnetism greater than 4V 25Hz
Input power Supply:AC 160~260V 50/60Hz
Maximum Output: DC 5A 95V(when the voltage reaches AC 240V)
Frequency Compensation:Built-in low speed protective circuit.INPUT:
Voltage Jumper selectable
95-132V ac or 190-264 Hz nominal
Frequency 50-60 Hz nominal
OUTPUT:
Voltage max 90V dc at 207V ac input
Current continuous 2A dc
Intermittent 5A for 10 secs
Resistance 20 ohms minimum
REGULATION: +/-1%This is one kinds of currency AVRs for brushless generators in the world.
TECHNICAL DATA:
INPUT:
Voltage :160-260V AC
Frequency :50-60 Hz nominalSKU: n/a -
AMF / ATS Controller, Generator, Genset Starting Module
DKG105 DATAKOM Generator Automatic Mains Failure control panel
AMF / ATS Controller, Generator, Genset Starting ModuleDKG105 DATAKOM Generator Automatic Mains Failure control panel
DKG-105 AUTOMATIC MAINS FAILURE UNIT
The DKG-105 automatic mains failure unit is a microprocessor based digital unit offering all functions needed for the automatic control of a genset.
The unit fits into a standard 72x72mm panel meter opening and offers a very cost effective and
space saving solution for the basic genset control.
In automatic mode, the unit monitors 3 phases of the mains voltage and controls the automatic starting, stopping and load transfer of the generator.
Once the generator is running, the device monitors the internal protections and external fault inputs.
DKG-105 provides a full set of digitally adjustable timers and threshold levels. Also the relay configuration is programmable, enabling the control of various types of engines, including gasoline engines.
The programs may be modified by the customer via pushbuttons on the unit, and do not require an external unit.
Automatic engine starting and stopping Gas engine support
Automatic mains failure monitoring
Automatic load transfer
Automatic shutdown on fault condition
Test mode available
Survives cranking dropouts
Digital engine run-hours display
Provision for energize to stop, preheat & choke outputs
Mains phases voltage limits checking
Generator phase voltage limits checking
SKU: n/a -
AMF / ATS Controller, Generator, Genset Starting Module
DSE 704 Auto Start Generator Control Panel Alternator
AMF / ATS Controller, Generator, Genset Starting ModuleDSE 704 Auto Start Generator Control Panel Alternator
Features:
- The automatic (utility) sector provides monitoring
- Automatic shutdown when fault conditions are detected
- Manual start
- Engine preheating
- Motor monitoring and protection functions
- Protected semiconductor outputs (PSS)
- Front panel mounting
- Front panel programming
- Tamper-proof engine hour counter
- Remote start
- LED indicators
- Configurable timers
- Configurable outputs
- Single-phase / three-phase hand detection
SKU: n/a -
There are no reviews yet.