Recommended Products
Infrared Motion Sensor Pir Body Sensor Switch Infrared Motion Sensor Detector for Led Lamp Home Garden 90~250VInfrared Motion Sensor Pir Body Sensor Switch Infrared Motion Sensor Detector for Led Lamp Home Garden 90~250V
Infrared Motion Sensor Pir Body Sensor Switch Infrared Motion Sensor Detector for Led Lamp Home Garden 90~250VInfrared Motion Sensor Pir Body Sensor Switch Infrared Motion Sensor Detector for Led Lamp Home Garden 90~250V
Specifications:
Type: Sensor Switch
Material: ABS
Motion Angle: 180 Degree
Motion Distance: 2-8m / 6.6-26.2ft
Rotate Angle: 180 Degree
Working Voltage: 85-265V
Power: 30W
Waterproof: IP54
Installation Height: 1.8m- 2.5m / 5.9- 9.2ft
Work Temperature: -10 – 40 celsius
Work Humidity: Max 93%
Delay Time: 5+/-2 second – 4+/-1 min
Cable Length: 140mm / 5.5″
Item Size: 8*4.2*4cm / 3.1*1.7*1.6″(L*W*H)
Net Weight: 33g / 1.2oz
TJC4024T032_011R 3.2 inch USART HMI touch screen with GPU font picture configuration screen serial port TFT LCD screen
TJC4024T032_011R 3.2 inch USART HMI touch screen with GPU font picture configuration screen serial port TFT LCD screen
3.2 inch Nextion TFT HMI LCD Touchscreen NX8048K050 is a Seamless Human Machine Interface (HMI) solution. 3.2Ā inch Nextion TFT HMI LCD Touchscreen NX8048K050 that provides a control and visualization interface between a human and a process, machine, application or appliance. Nextion is mainly…
DTA-4158 Battery Charger Digital 24V/30A & 24V/50A For Generator
DTA-4158 Battery Charger Digital 24V/30A & 24V/50A For Generator
FEATURES
DTA-4072 Battery Charger 24V/5A For Generator
FEATURES
DTA-11099 Water Level Switch For Boiler
DTA-11099 Water Level Switch For Boiler
ABO-20L Single Beam Detector Active Half Egg Beam Infrared Detector Photoelectric Sensor, Detect Distance: 20m
ABO-20L Single Beam Detector Active Half Egg Beam Infrared Detector Photoelectric Sensor, Detect Distance: 20m
Item | Parameter |
Model | ABL-20L |
Power supply
|
DC 10.5V–24V/0.5V
|
Maximum current
|
TX: 15mA MAXĀ RX: 30mAĀ MAX
|
Optical source
|
Infrared Pulse
|
Infrared wave length
|
940nm
|
Infrared transmission frequency
|
1.92KHz
|
Response speed
|
50ms
|
Alarm output time
|
ā„1s
|
Detection mode
|
Block off the infrared beam
|
Infrared angle
|
<Ā±10Ā°
|
Infrared distance
|
ā¤20m
|
Waterproof level | IP55 |
Relay contact capacity
|
AC,DC30V,0.5A max
|
Working environment
|
Temperature: -25Ā°C-+55Ā°C; Humidity: RH95%
|
Product dimension
|
76*49*29mm
|
IR Infrared Beam Sensor with 2 Beams Detector Outdoor Active (ABT-150)
IR Infrared Beam Sensor with 2 Beams Detector Outdoor Active (ABT-150)
Response speed: 50 to 700m/sec adjustable
Alarm output: 1C relay contact output, contact capability DC30v/0.5A max
Power and voltage: DC12~24V, AC 11~18V
Working temperature: -25 ~ 55 degree C
Tamper output: 1B contact output, DC30V/0.5A max
Optical axis adjust angle(horizontal): 180Ā° (Ā± 90Ā° )
Optical axis adjust angle(vertical): 20Ā° (Ā± 10Ā° )
Weight: 300g for transmitter; 300g for receiver; 1000g for each pack (including bracket)
Valid length: 17CM
Shop
Showing 1–24 of 95 results
-
Automatic Day Night Sensor, Sensor's
12DC Automatic Light Control Sun Switch 10A Photosensor Photocell Sensor
Automatic Day Night Sensor, Sensor's12DC Automatic Light Control Sun Switch 10A Photosensor Photocell Sensor
- Working Voltage: 12V DC
- Rated Current: 10A
- Operating Temperature: -20C ā +50C
- Power Consumption: 0.5W Max.
- Fixing Hole Diameter: 4.9mm / 0.2ā³;Size : 3.3 x 4.2 x 5cm / 1.3ā³ x 1.7ā³ x 2ā³(L*W*H)
- External Material: Plastic
- Color: White, Blue
SKU: n/a -
Motion Sensor's, Sensor's
360 Degree PIR Motion Movement Sensor Switch 220-240V 1200W Time and LUX Adjustable Light Switch for LED Lights White
Motion Sensor's, Sensor's360 Degree PIR Motion Movement Sensor Switch 220-240V 1200W Time and LUX Adjustable Light Switch for LED Lights White
Product Description
Quality control standard- 360 Degree Ceiling Mount PIR Motion-Sensor Lamp
- Operating volt: ac 220-250v 50hz-60hz.
- Load power: upto 300/1200w max
- Ambient light: 3-2000 (adjuestable)
- Load type: incandescent lamp, led light, clf, fans, etc
- Detecting distance: 0~7m
- Detecting angle: 360 degree.
- Installtion hight: 2.2-4 mtr
- Motion detetion speed: 0.6~1m/s
- Power cusumption: 0.1w (static) & 0.4(work)
- Working humidity: less than 93%rh
- Delay: 10 seconds -7 minutes (adjustable)
SKU: n/a -
Motion Sensor's, Sensor's
40mm AC 220V Infrared PIR Motion Sensor Automatically Light On Off Sensor
- Specifications:
- Type: PIR Switch
- Color: White
- Working Voltage/Frequency:AC100-240V, 50/60Hz
- Output power : ā¤40W
- Photo sensing Setting:ā¤2Lux, ā¤25Lux, 2000Lux
- Sensing Distance: 4-6m
- Time delaya djustment :15secs 45secs 5mins
- Angle Coverage: 110Ā°
- Extreme Temperature Using:-10Ā°ā+45Ā°
- Stand by power consumption:<0.1W
- Size:45 mmx 40mm x 25mm
- Package Contents:
- 1 x PIR Motion SensorSwitch
SKU: n/a -
Infrared Beam Active Sensor, Sensor's
ABO-20L Single Beam Detector Active Half Egg Beam Infrared Detector Photoelectric Sensor, Detect Distance: 20m
Infrared Beam Active Sensor, Sensor'sABO-20L Single Beam Detector Active Half Egg Beam Infrared Detector Photoelectric Sensor, Detect Distance: 20m
Item Parameter Model ABL-20L Power supplyDC 10.5V–24V/0.5VMaximum currentTX: 15mA MAXĀ RX: 30mAĀ MAXOptical sourceInfrared PulseInfrared wave length940nmInfrared transmission frequency1.92KHzResponse speed50msAlarm output timeā„1sDetection modeBlock off the infrared beamInfrared angle<Ā±10Ā°Infrared distanceā¤20mWaterproof level IP55 Relay contact capacityAC,DC30V,0.5A maxWorking environmentTemperature: -25Ā°C-+55Ā°C; Humidity: RH95%Product dimension76*49*29mmSKU: n/a -
Different Types Of Sensor's, Sensor's
Aosong original AM2302 Digital Temperature Sensor / Humidity Sensor For Arduino DHT22
Different Types Of Sensor's, Sensor'sAosong original AM2302 Digital Temperature Sensor / Humidity Sensor For Arduino DHT22
The DHT22 combined temperature and relative humidity sensor provides a simple and low-cost solution.
To differentiate between the two readings, the DHT22 makes use of a simple protocol on a single data pin which is best interpreted by using existing library code. The instructions below show how to connect the DHT22 up to your Particle Argon, and take you through the process of finding and including the right library in your application code using the Web IDE.This example is based on the Adafruit version that is provided with the library code, and the Photon Maker Kit tutorial linked in the box above.SKU: n/a -
-
Uncategorized
AVR R250 Automatic Voltage Regulator Controls Module Card For Leroy SomerAVR R250 Automatic Voltage Regulator Controls Module Card For Leroy Somer
UncategorizedAVR R250 Automatic Voltage Regulator Controls Module Card For Leroy SomerAVR R250 Automatic Voltage Regulator Controls Module Card For Leroy Somer
Description: Condition: 100% new
Material: Metal & plastic
Package included: 1 pcĀ AVR
Application(just for reference):Ā
AVR R250
NEW Automatic Voltage Regulator AVR Controls Module Card R250 For Leroy Somer
Technical specification:
Voltage regulation: around +/-0.5%
Voltage supply/sensing range 85 to 139 V (50/60Hz)
Rapid response time (500ms) for a transient voltage variation amplitude of +/-20%
Voltage setting p1
Stability setting p2
Supply protected with an 8A fuse, slow action(supports 10A for 10s)
SKU: n/a -
Arduino Board, Students Gallery
Current To Voltage Module 0 -20mA/4 -20mA to 0- 3.3V/0 -5V/0 -10V Voltage Transmitter Signal Converter Module
Arduino Board, Students GalleryCurrent To Voltage Module 0 -20mA/4 -20mA to 0- 3.3V/0 -5V/0 -10V Voltage Transmitter Signal Converter Module
- Supply Voltage: 7-36V
- Voltage Output Supports: 0-3.3V 0-5V 0-10V.
- Current Input Supports: 4-20mA and 0-20mA
- Size: 42.2 * 25.9 (mm)
-
Instruction:
1. The module is connected according to the definition, the supply voltage is 7-36V (if the output is to 10V, the supply voltage must be greater than 12V)
2. After power on, the D2 light should be bright, otherwise please check the line connection. Board with reverse connection protection, reverse connection not burning.3. When the current input is minimum (0mA or 4mA), adjust the ZERO potentiometer, so that the output of VOUT is minimum (0.0V or other voltage)4. When the current input is the maximum (20mA), adjust the SPAN potentiometer, so that the VOUT output is the maximum value (3.3V or 5V or 10V, when the input is 4-20mA, the minimum output can be 2.5V).According to your needs, select the corresponding range by jumper cap:
4–20ma:0–2.5V range: J1 1, 2 feet short connection, 3, 4 feet short connection
0–3.3V range: J1 1, 2 feet off, 3, 4 feet off
0–5.0V range: J1 1, 2 feet short connection, 3, 4 feet short connection
0–10.0V range: J1 1, 2 feet short connection, 3, 4 feet off
0–20ma:0–3.3V range: J1 1, 2 feet short connection, 3, 4 feet short connection
0–5.0V range: J1 1, 2 feet short connection, 3, 4 feet short connection
0–10.0V range: J1 1, 2 feet short connection, 3, 4 feet off
SKU: n/a -
AMF / ATS Controller, Generator, Genset Starting Module
DKG105 DATAKOM Generator Automatic Mains Failure control panel
AMF / ATS Controller, Generator, Genset Starting ModuleDKG105 DATAKOM Generator Automatic Mains Failure control panel
DKG-105 AUTOMATIC MAINS FAILURE UNIT
The DKG-105 automaticĀ mains failure unit is a microprocessor basedĀ digital unit offering all functions needed for theĀ automatic control of a genset.Ā
The unit fits into a standard 72x72mm panelĀ meter opening and offers a very cost effective and
space saving solution for the basic genset control.Ā
In automatic mode, the unit monitors 3 phasesĀ of the mains voltage and controls the automaticĀ starting, stopping and load transfer of theĀ generator.
Once the generator is running, theĀ device monitors the internal protections andĀ external fault inputs.
DKG-105 provides a full set of digitallyĀ adjustable timers and threshold levels. Also theĀ relay configuration is programmable, enabling theĀ control of various types of engines, includingĀ gasoline engines.
The programs may be modifiedĀ by the customer via pushbuttons on the unit, andĀ do not require an external unit.
Automatic engine starting and stopping Gas engine support
Automatic mains failure monitoring
Automatic load transfer
Automatic shutdown on fault condition
Test mode available
Survives cranking dropouts
Digital engine run-hours display
Provision for energize to stop, preheat & choke outputs
Mains phases voltage limits checking
Generator phase voltage limits checking
SKU: n/a -
AMF / ATS Controller, Generator, Genset Starting Module
DSE 704 Auto Start Generator Control Panel Alternator
AMF / ATS Controller, Generator, Genset Starting ModuleDSE 704 Auto Start Generator Control Panel Alternator
Features:
- The automatic (utility) sector provides monitoring
- Automatic shutdown when fault conditions are detected
- Manual start
- Engine preheating
- Motor monitoring and protection functions
- Protected semiconductor outputs (PSS)
- Front panel mounting
- Front panel programming
- Tamper-proof engine hour counter
- Remote start
- LED indicators
- Configurable timers
- Configurable outputs
- Single-phase / three-phase hand detection
SKU: n/a -
PWM Solar Charge Controller, Solar Charge controller
DST-2430 Solar Charge Controller Digital PWM 12/24V 30A
PWM Solar Charge Controller, Solar Charge controllerDST-2430 Solar Charge Controller Digital PWM 12/24V 30A
- Model No:DST 2430
- SOLAR CHARGE CONTROLLER DIGITAL.
- voltage:12/24V.
- Rated current:30A.
- Method:PWM.
- Warranty : 1 year.
- Microprocessor Controlled System.
- Programmable Lcd Display.
- 5 mode Of Lcd Display Scrolling.
- All Parameters Can be Program From Menu.
- Memorized The Set Parameters.
- Charging Can Be Stopped When Battery Voltage Reaching
- The Set Value ( charging off volt ).
- 3 Methods Of Battery Charging.
- Charge And Full Battery Indicator.
- Intelligentized The Temperature Compensation.
- Over Charge Protection.
- Over current Protection.
- Short Circuit Protection.
- Reverse Discharge Protection.
- Reverse Polarity Connection protection.
SKU: n/a -
PWM Solar Charge Controller, Solar Charge controller, Solar Hybrid System
DST-2430HB Solar Charge Controller PWM With Hybrid System 12V/24V 30A HB
PWM Solar Charge Controller, Solar Charge controller, Solar Hybrid SystemDST-2430HB Solar Charge Controller PWM With Hybrid System 12V/24V 30A HB
- Model DST 2430HB
- voltage:12/24V
- Rated current:30A.
- Method:PWM.
- Microprocessor Controlled System.
- Programmable Lcd Display.
- All Parameters Can be Program From Menu.
- UPS In Automatic On/OFF Control
- Warranty 1 Year
- Memorized The Set Parameters.
- Charging Can Be Stopped When Battery Voltage Reaching The Set Value ( charging off volt ).
- 3 Methods Of Battery Charging. Charge And Full Battery Indicator.
- Intelligentized The Temperature Compensation.
- Over Charge Protection.
- Solar ATS/Hybrid System Control Your UPS InPut 220V
- Automatic Detection of voltage Solar Panel & Battery.
- UPS Input 220v Can Be Stopped When Battery Voltage & Solar Voltage Reaching The Set Value.
- When Solar Panel Volt/Battery Volt Down The Set Value Then Hybrid system Connect The UPS Input With Wapda Electricity.
- Intelligent Solar ATS/Hybrid System to minimize the use of Electricity and Maximize The Use of Solar Panel Energy In Order to Reduce Utility Bills.
SKU: n/a -
PWM Solar Charge Controller, Solar Charge controller
DST-2450 Solar Charge Controller PWM With Hybrid System 12V/24V 50A HB
PWM Solar Charge Controller, Solar Charge controllerDST-2450 Solar Charge Controller PWM With Hybrid System 12V/24V 50A HB
- Model DST 2450HB
- voltage:12/24V
- Rated current:50A.
- Method:PWM.
- Microprocessor Controlled System.
- Programmable Lcd Display.
- All Parameters Can be Program From Menu.
- UPS In Automatic On/OFF Control
- Warranty 1 Year
- Memorized The Set Parameters.
- Charging Can Be Stopped When Battery Voltage Reaching The Set Value ( charging off volt ).
- 3 Methods Of Battery Charging. Charge And Full Battery Indicator.
- Intelligentized The Temperature Compensation.
- Over Charge Protection.
- Solar ATS/Hybrid System Control Your UPS InPut 220V
- Automatic Detection of voltage Solar Panel & Battery.
- UPS Input 220v Can Be Stopped When Battery Voltage & Solar Voltage Reaching The Set Value.
- When Solar Panel Volt/Battery Volt Down The Set Value Then Hybrid system Connect The UPS Input With Wapda Electricity.
- Intelligent Solar ATS/Hybrid System to minimize the use of Electricity and Maximize The Use of Solar Panel Energy In Order to Reduce Utility Bills.
SKU: n/a -
MPPT Solar Charge Controller, PWM Solar Charge Controller, Solar Charge controller, Solar Hybrid System
DST-2480MP Solar Charge Controller MPPT With Hybrid System 12V/24V 80A
MPPT Solar Charge Controller, PWM Solar Charge Controller, Solar Charge controller, Solar Hybrid SystemDST-2480MP Solar Charge Controller MPPT With Hybrid System 12V/24V 80A
- Model DST 2480MPPT
- Battery Voltage:12/24V
- Rated current:80A.
- Method:MPPT.
- Pv Voltage: 100V
- Automatic Battery Voltage Detect.
- Microprocessor Controlled System.
- Programmable Lcd Display.
All Parameters Can be Program From Menu. - UPS In Automatic On/OFF Control.
- Memorized The Set Parameters.
- Charging Can Be Stopped When Battery Voltage Reaching The Set Value ( charging off volt ).
- Efficient Methods Of Battery Charging. Charge And Full Battery Indicator.
- Intelligentized The Temperature Compensation.
- Automatic Cooling System Installed With 2 Fans.
- Over Charge Protection.
- Solar ATS/Hybrid System Control Your UPS InPut 220V
- Automatic Detection of voltage Solar Panel & Battery.
- UPS Input 220v Can Be Stopped When Battery Voltage & Solar Voltage Reaching The Set Value.
- When Solar Panel Volt/Battery Volt Down The Set Value Then Hybrid system Connect The UPS Input With Wapda Electricity.
- Warranty: 1Year
SKU: n/a -
PWM Solar Charge Controller, Solar Charge controller, Solar Hybrid System
DST-4126 Solar Hybrid System Digital 12V,24V
PWM Solar Charge Controller, Solar Charge controller, Solar Hybrid SystemDST-4126 Solar Hybrid System Digital 12V,24V
- Model No:DST 4126
- Voltage:12/24V
- Digital Solar ATS/Hybrid System.
- Solar ATS/Hybrid System Control Your UPS InPut 220V.
- Automatic Detection of voltage Solar Panel & Battery.
- UPS Input 220v Can Be Stopped When Battery Voltage & Solar Voltage Reaching The Set Value.
- When Solar Panel Volt/Battery Volt Down The Set Value Then Hybrid system Connect The UPS Input With Wapda Electricity.
- Intelligent Solar ATS/Hybrid System to minimize the use of Electricity and Maximize The Use of Solar Panel Energy
- In Order to Reduce Utility Bills.
SKU: n/a -
-
AMF / ATS Controller, Generator
DTA-110 Generator AMF/ATS Control Card With Heater Disele Generator
- Auto Main Failure and Automatic load transfer unit
- Microprocessor controled
- The Heater Turns on for About Six Seconds Before Turning on the Self
- Self On/Off Time Setting
- Genset On Load Time & Genset Off Load Time
- Main On Load Time
- Generator Cool Down Time Built in 40 Seconds
- Failed To Start Indication LED
- Excellent Ability to Start and Stop the Generator
- DC Supply: 12 Volts, (+) and (-) Terminals.
- Indicators to show card performance
- Capability to transfer loads without DC 12 volts
- There is an extra Switchs to start and stop the generator manually
SKU: n/a -
Boiler Controller, Water Pump Controller
DTA-11046 Boiler Control Card with Pressure Safety & Contector Control Naomoto
Boiler Controller, Water Pump ControllerDTA-11046 Boiler Control Card with Pressure Safety & Contector Control Naomoto
- Model No. 11046 Naomoto Boiler
- Input voltage 220V AC
- Output Voltage 220Ac
- Rated Current . 5A AC For Contector
- Has a strong ability to sense water
- Time Delay Setting forĀ Contector Coil
- Ā Pressure Switch Nc Point
- APPLICATIONS
- Steam Boiler
SKU: n/a -
Boiler Controller, Water Level & Pump Controller, Water Pump Controller
DTA-11085 Water Level Control Card with Burner Safety and Pressure Safety For Steam Boiler
Boiler Controller, Water Level & Pump Controller, Water Pump ControllerDTA-11085 Water Level Control Card with Burner Safety and Pressure Safety For Steam Boiler
- Model No. 11085
- Input voltage 220V AC
- Output Voltage 220Ac
- Rated Current . 15A AC For pump
- Has a strong ability to sense water
- Time Delay Setting for Pump On
- Time Setting for Pressure Switch On
- APPLICATIONS
- Steam Boiler
- Water heaters
SKU: n/a -
Boiler Controller, Water Level & Pump Controller, Water Pump Controller
DTA-11099 Water Level Switch For Boiler
Boiler Controller, Water Level & Pump Controller, Water Pump ControllerDTA-11099 Water Level Switch For Boiler
- Model No: DTA-11099
- Input Voltage 220V
- Rated Current: 12A Continuously
- It Can be Installed Very Easily
- 2 Wirer Sensing
- When the water touches the High level, the motor should stop
- After leaving the high level, the Motor should turn on after the time
- Microprocessor Based and very Efficient
SKU: n/a -
Boiler Controller, Water Level & Pump Controller, Water Pump Controller
DTA-11100 Water Motor Automatic & Manual Control With Water Level System
Boiler Controller, Water Level & Pump Controller, Water Pump ControllerDTA-11100 Water Motor Automatic & Manual Control With Water Level System
- Input Voltage 220V
- Rated Current: 12A Continuously
- Led Indicators to Indicate Water Level
- Button to Operate the Motor Manually or Automatically
- In the Case of Automatic Mode, if the Water Drops Below 60%, the Motor will Automatically Turn on and Stop at 100%.
- In Case of Choosing Manual Mode, the Motor will On itselfĀ From the Button and will be shut off at 100% Water Filling.
- It Can be Installed Very Easily
- This device is designed to do its job very well
- 6 Core Wire will be Used to Make the Sensor
SKU: n/a -
Boiler Controller, Water Level & Pump Controller, Water Pump Controller
DTA-11104 Water Motor Automatic Control System Card
Boiler Controller, Water Level & Pump Controller, Water Pump ControllerDTA-11104 Water Motor Automatic Control System Card
- Model No: DTA-11104
- Water Level Switch For Motor & Boiler
- Input Voltage 220V
- Torque Current 10A AC
- Rated Current: 4AĀ AC Continuously
- It Can be Installed Very Easily
- 3 Wirer Sensing
- 1Ā ComĀ
- 2Ā Low Level For Automatic Motor Strat
- 3Ā Hi Leve For Automatic Motor Stop
- After leaving the Low level, the Motor should turn on after the time
- When the water touches the High level, the motor should stop
- Microprocessor Based and very Efficient
SKU: n/a -
Boiler Controller, Water Level & Pump Controller, Water Pump Controller
DTA-11104B Water Motor Automatic Control System Card
Boiler Controller, Water Level & Pump Controller, Water Pump ControllerDTA-11104B Water Motor Automatic Control System Card
- Model No: DTA-11104 Big
- Water Level Switch For Motor & Boiler
- Input Voltage 220V
- Torque Current 25A AC
- Rated Current: 12AĀ AC Continuously
- It Can be Installed Very Easily
- 3 Wirer Sensing
- 1Ā ComĀ
- 2Ā Low Level For Automatic Motor Strat
- 3Ā Hi Leve For Automatic Motor Stop
- After leaving the Low level, the Motor should turn on after the time
- When the water touches the High level, the motor should stop
- Microprocessor Based and very Efficient
SKU: n/a