AMF / ATS Controller, Generator, Genset Starting Module
DSE 704 Auto Start Generator Control Panel Alternator
Features:
- The automatic (utility) sector provides monitoring
- Automatic shutdown when fault conditions are detected
- Manual start
- Engine preheating
- Motor monitoring and protection functions
- Protected semiconductor outputs (PSS)
- Front panel mounting
- Front panel programming
- Tamper-proof engine hour counter
- Remote start
- LED indicators
- Configurable timers
- Configurable outputs
- Single-phase / three-phase hand detection
₨7,500
Description
The DSE 704 Generator Controller is an Automatic Mains Failure Control Module that provides an excellent range of engine monitoring and protection functions. The module has been designed to monitor engine temperature, low oil pressure, start failure, load failure, Overspeed, and under speed.
Based on 0 reviews
Be the first to review “DSE 704 Auto Start Generator Control Panel Alternator”
Related products
-
AVR, Generator
R230 AVR Automatic Voltage Regulator for Single-Phase Two-Wire Generator
- 100% brand new and high quality.
- This product is a AVR(Automatic Voltage Regulator) for brushless alternator with adjustable voltage.
- The regulator monitors the exciter excitation current as a function of the alternator output voltage.
- Very simple in design, the alternator with shunt excitation has no sustaining short-circuit capacity.
- Made with flame retardant and heat resisting material, stable and reliable to use.
- Input
Voltage 85-139 VAC
Frequency 50-60 Hz nominal
Output
Voltage max 75 V DC at 100V AC input
Current continuous 4A DC
Intermittent 8A
Resistance 15 ohms minimum
Regulation +/- 0.5%
SKU: n/a -
AMF / ATS Controller, Generator
DTA-110 Generator AMF/ATS Control Card With Heater Disele Generator
- Auto Main Failure and Automatic load transfer unit
- Microprocessor controled
- The Heater Turns on for About Six Seconds Before Turning on the Self
- Self On/Off Time Setting
- Genset On Load Time & Genset Off Load Time
- Main On Load Time
- Generator Cool Down Time Built in 40 Seconds
- Failed To Start Indication LED
- Excellent Ability to Start and Stop the Generator
- DC Supply: 12 Volts, (+) and (-) Terminals.
- Indicators to show card performance
- Capability to transfer loads without DC 12 volts
- There is an extra Switchs to start and stop the generator manually
SKU: n/a -
AMF / ATS Controller, Generator
DTA-201 Generator AMF/ATS Control Card With Heater & Low Oil Pressure & High Temperature Switch Safety
AMF / ATS Controller, GeneratorDTA-201 Generator AMF/ATS Control Card With Heater & Low Oil Pressure & High Temperature Switch Safety
Auto Main Failure and Automatic load transfer With Heater & Low Oil Pressure & High Temperature Switch Safety
- Microprocessor controled
- The Heater Turns on for About 9 Seconds Before Turning on the Self
- Self On/Off Time Setting
- Genset On Load Time & Genset Off Load Time
- Main On Load Time
- Generator Cool Down Time Built in 14 Seconds
- Failed To Start Indication LED
- Excellent Ability to Start and Stop the Generator
- DC Supply: 12 Volts, (+) and (-) Terminals.
- Indicators to show card performance
- Capability to transfer loads without DC 12 volts
- There is an extra Switch to start and stop the generator manually
SKU: n/a -
AMF / ATS Controller, Generator
DTA-210 AMF/ATS 2 Wapda & 1 Generator Automatic Load Transfer and Generator Start/Stop Unit
AMF / ATS Controller, GeneratorDTA-210 AMF/ATS 2 Wapda & 1 Generator Automatic Load Transfer and Generator Start/Stop Unit
- Aoutmatic 2 main Lines And Generator Control Card
- This card is Specially Designed to Control Two WAPDA Meters and One Generator
- Meter 1 and Meter 2 automatically switch with time Delay Setting
- In case of both line shutdown, it starts the generator itself and shifts the load to the generator.
- If in-wapda 2 comes on while the generator is running, it shuts down the generator and turns it into Metter 2.and shifts the load to the Metter 2.
- In case of both Line 1 and Line 2 coming, the load of Line 1 will be transferred automatically
- Variables to Onload line one, line two, and line three
- Self On/Off Time Setting
- Genset On Load Time & Genset Off Load Time
- Main On Load Time
- Generator Cool Down Time
- Failed To Start Indication LED
- Excellent Ability to Start and Stop the Generator
- DC Supply: 12 Volts, (+) and (-) Terminals.
- Indicators to show card performance
- Capability to transfer loads without DC 12 volts
SKU: n/a
There are no reviews yet.